Part 24

Owing to the rapidly diminishing differences of the values of the sines as the upper end of the scale is approached, the sines of angles between 60° and 90° cannot be accurately determined in the foregoing manner. It is therefore advisable to calculate the value of the sine by means of the formula:

Sine θ = 1 − 2 sin^2 (90 − θ)/(2).

To determine the value of sin^2 (90 − θ)/(2). With the slide in the normal position, set the value of (90 − θ)/(2). on S to the index on the under-side of the rule, and read off the value x on B under the R.H. index of A. Without moving the slide find x on A, and read under it on B the value required.

EX.—Find value of sine 79° 40′.

Sine 79° 40′ = 1 − 2sin^2 5° 10′.

But sine 5° 10′ = 0·0900, and under this value on A is 0·0081 on B. Therefore sine 79° 40′ = 1 − 0·0162 = 0·9838.

The sines of very small angles, being very nearly proportional to the angles themselves, are found by direct reading. To facilitate this, some rules are provided with two marks, one of which, a single accent (′), corresponds to the logarithm of (1)/(sine 1′) and is found at the number 3438. The other mark—a double accent (″)—corresponds to the logarithm of (1)/(sine 1″) and is found at the number 206,265. In some rules these marks are found on either the A or the B scales; sometimes they are on both. In either case the angle on the one scale is placed so as to coincide with the significant mark on the other, and the result read off on the first-named scale opposite the index of the second.

In sines of angles under 3″, the number of integers in the result is −5; while it is −4 for angles from 3″ to 21″; −3 from 21″ to 3′ 27″; and −2 from 3′ 27″ to 34′ 23″.

EX.—Find sine 6′.

Placing the significant mark for minutes coincident with 6, the value opposite the index is found to be 175, and by the rule above this is to be read 0·00175. For angles in seconds the other significant mark is used; while angles expressed in minutes and seconds are to be first reduced to seconds. Thus, 3′ 10″ = 190″.

Tangents of Angles.—There remains to be considered the third scale found on the back of the slide, and usually distinguished from the others by being lettered T. In most of the more recent forms of rule this scale is placed near the lower edge of the slide, but in some arrangements it is found to be the centre scale of the three. Again, in some rules this scale is figured in the same direction as the scale of sines—viz., from left to right,—while in others the T scale is reversed. In both cases there is now usually an aperture formed in the back of the left extremity of the rule, with an index mark similar to that already referred to in connection with the scale of sines. Considering what has been referred to as the more general arrangement, the method of determining the tangents of angles may be thus explained:—

The tangent scale will be found to commence, in some rules, at about 34′, or, precisely, at the angle whose tangent is 0·01. More usually, however, the scale will be found to commence at about 5° 43′, or at the angle whose tangent is 0·1. The other extremity of the scale corresponds in all cases to 45°, or the angle whose tangent is 1. This explanation will suggest the method of using the scale, however it may be arranged. If the graduations commence with 34′, the T scale is to be used in conjunction with the right and left scales of A; while if they commence with 5° 43′ it is to be used in conjunction with the D scale.

In the former case the slide is to be placed in the rule so that the T scale is adjacent to the A scales, and, with the right and left indices coinciding, when opposite any angle on T will be found its tangent on A. From what has been said above, it follows that the tangents read on the L.H. scale of A have values extending from 0·01 to 0·1; while those read on the R.H. scale of A have values from 0·1 to 1·0. Otherwise expressed, to the values of any tangent read on the L.H. scale of A a cypher is to be prefixed; while if found on the R.H. scale, it is read directly as a decimal.

EX.—Find tan. 3° 50′.

Placing the slide as directed, the reading on A opposite 3° 50′ on T is found to be 67. As this is found on the L.H. scale of A, it is to be read as 0·067.

EX.—Find tan. 17° 45′.

Here the reading on A opposite 17° 45′ on T is 32, and as it is found on the R.H. scale of A it is read as 0·32.

As in the case of the scale of sines, the tangents may be found without reversing the slide, when a fixed index is provided in the back of the rule for the T scale.

We revert now to a consideration of those rules in which a single tangent scale is provided. It will be understood that in this case the slide is placed so that the scale T is adjacent to the D scale, and that when the indices of both are placed in agreement, the value of the tangent of any angle on T (from 5° 43′ to 45°) may be read off on D, the result so found being read as wholly decimal. Thus tan. 13° 20′ is read 0·237.

If a back index is provided, the slide is used in its normal position, when, setting the angle on the tangent scale to this index, the result can be read on C over the L.H. index of D.

The tangents of angles above 45° are obtained by the formula: Tan. θ = (1)/(tan. (90 − θ)). For all angles from 45° to (90° − 5° 43′) we proceed as follows:—Place (90 − θ) on T to the R.H. index of D, and read tan. θ on D under the L.H. index of T. The first figure in the value thus obtained is to be read as an integer. Thus, to find tan. 71° 20′ we place 90° − 71° 20′ = 18° 40′ on T, to the R.H. index of D, and under the L.H. index of T read 2·96, the required tangent.

The tangents of angles less than 40′ are sensibly proportional to the angles themselves, and as they may therefore be considered as sines, their value is determined by the aid of the single and double accent marks on the sine scale, as previously explained. The rules for the number of integers are the same as for the sines.

Multiplication and division of tangents may be quite readily effected.

EX.—Tan. 21° 50′ × 15 = 6.

Set L.H. index of T to 15 on D, and under 21° 50′ on T read 6 on D.

EX.—Tan. 72° 40′ × 117 = 375.

Set (90° − 72° 40′) = 17° 20′ on T to 117 on D, and under R.H. index of T read 375 on D.

Cosines of Angles.—The cosines of angles may be determined by placing the scale S with its indices coinciding with those of A, and when opposite (90 − θ) on S is read cos. θ on A. If the result is read on the L.H. scale of A, a cypher is to be prefixed to the value read; while if it is read on the R.H. scale of A, the value is read directly as a decimal. Thus, to determine cos. 86° 30′ we find opposite (90° − 86° 30′) = 3° 30′ on S, 61° on A, and as this is on the L.H. scale the result is read 0·061. Again, to find cos. 59° 20′ we read opposite (90° − 59° 20′) or 30° 40′ on S, 51 on A, and as this is found on the R.H. scale of A, it is read 0·51.