Part 5

Fig. 4.

The fourth quarter of a turn of the axis will move forward one division all the dials marked (*); and the arrangement will finally assume the form exhibited in fig. 5, in which the calculation is completed. The first row T in this expresses the fifth power of 7; and the second expresses the number which must be added to the first row, in order to produce the fifth power of 8; the numbers in each row being prepared for the change which they must undergo, in order to enable them to continue the computation according to the method of alternate addition here adopted.

Fig. 5.

Having thus explained what it is that the mechanism is required to do, we shall now attempt to convey at least a general notion of some of the mechanical contrivances by which the desired ends are attained. To simplify the explanation, let us first take one particular instance--the dials B and B^1, fig. 1, for example. Behind the dial B^1 is a bolt, which, at the commencement of the process, is shot between the teeth of a wheel which drives the dial B: during the first quarter of a turn this bolt is made to revolve, and if it continued to be engaged in the teeth of the said wheel, it would cause the dial B to make a complete revolution; but it is necessary that the dial B should only move through three divisions, and, therefore, when three divisions of this dial have passed under its index, the aforesaid bolt must be withdrawn: this is accomplished by a small wedge, which is placed in a fixed position on the wheel behind the dial B^1, and that position is such that this wedge will press upon the bolt in such a manner, that at the moment when three divisions of the dial B have passed under the index, it shall withdraw the bolt from the teeth of the wheel which it drives. The bolt will continue to revolve during the remainder of the first quarter of a turn of the axis, but it will no longer drive the dial B, which will remain quiescent. Had the figure at the index of the dial B^1 been any other, the wedge which withdraws the bolt would have assumed a different position, and would have withdrawn the bolt at a different time, but at a time always corresponding with the number under the index of the dial B^1: thus, if 5 had been under the index of the dial B^1, then the bolt would have been withdrawn from between the teeth of the wheel which it drives, when five divisions of the dial B had passed under the index, and so on. Behind each dial in the row D^1 there is a similar bolt and a similar withdrawing wedge, and the action upon the dial above is transmitted and suspended in precisely the same manner. Like observations will be applicable to all the dials in the scheme here referred to, in reference to their adding actions upon those above them.

There is, however, a particular case which here merits notice: it is the case in which 0 is under the index of the dial from which the addition is to be transmitted upwards. As in that case nothing is to be added, a mechanical provision should be made to prevent the bolt from engaging in the teeth of the wheel which acts upon the dial above: the wedge which causes the bolt to be withdrawn, is thrown into such a position as to render it impossible that the bolt should be shot, or that it should enter between the teeth of the wheel, which in other cases it drives. But inasmuch as the usual means of shooting the bolt would still act, a strain would necessarily take place in the parts of the mechanism, owing to the bolt not yielding to the usual impulse. A small shoulder is therefore provided, which puts aside, in this case, the piece by which the bolt is usually struck, and allows the striking implement to pass without encountering the head of the bolt or any other obstruction. This mechanism is brought into play in the scheme, fig. 1, in the cases of all those dials in which 0 is under the index.

Such is a general description of the nature of the mechanism by which the adding process, apart from the carriages, is effected. During the first quarter of a turn, the bolts which drive the dials in the first, third, and fifth rows, are caused to revolve, and to act upon these dials, so long as they are permitted by the position of the several wedges on the second, fourth, and sixth rows of dials, by which these bolts are respectively withdrawn; and, during the third quarter of a turn, the bolts which drive the dials of the second and fourth rows are made to revolve and act upon these dials so long as the wedges on the dials of the third and fifth rows, which withdraw them, permit. It will hence be perceived, that, during the first and third quarters of a turn, the process of addition is continually passing upwards through the machinery; alternately from the even to the odd rows, and from the odd to the even rows, counting downwards.

We shall now attempt to convey some notion of the mechanism by which the process of carrying is effected during the second and fourth quarters of a turn of the axis. As before, we shall first explain it in reference to a particular instance. During the first quarter of a turn the wheel B^2, fig. 1, is caused by the adding bolt to move through five divisions; and the fifth of these divisions, which passes under the index, is that between 9 and 0. On the axis of the wheel C^2, immediately to the left of B^2, is fixed a wheel, called in mechanics a ratchet wheel, which is driven by a claw which constantly rests in its teeth. This claw is in such a position as to permit the wheel C^2 to move in obedience to the action of the adding bolt, but to resist its motion in the contrary direction. It is drawn back by a spiral spring, but its recoil is prevented by a hook which sustains it; which hook, however, is capable of being withdrawn, and when withdrawn, the aforesaid spiral spring would draw back the claw, and make it fall through one tooth of the ratchet wheel. Now, at the moment that the division between 9 and 0 on the dial B^2 passes under the index, a thumb placed on the axis of this dial touches a trigger which raises out of the notch the hook which sustains the claw just mentioned, and allows it to fall back by the recoil of the spring, and to drop into the next tooth of the ratchet wheel. This process, however, produces no immediate effect upon the position of the wheel C^2, and is merely preparatory to an action intended to take place during the second quarter of a turn of the moving axis. It is in effect a memorandum taken by the machine of a carriage to be made in the next quarter of a turn.

During the second quarter of a turn, a finger placed on the axis of the dial B^2 is made to revolve, and it encounters the heel of the above-mentioned claw. As it moves forward it drives the claw before it: and this claw, resting in the teeth of the ratchet wheel fixed upon the axis of the dial C^2 drives forward that wheel, and with it the dial. But the length and position of the finger which drives the claw limits its action, so as to move the claw forward through such a space only as will cause the dial C^2 to advance through a single division; at which point it is again caught and retained by the hook. This will be added to the number under its index, and the requisite carriage from B^2 to C^2 will be accomplished.

In connexion with every dial is placed a similar ratchet wheel with a similar claw, drawn by a similar spring, sustained by a similar hook, and acted upon by a similar thumb and trigger; and therefore the necessary carriages, throughout the whole machinery, take place in the same manner and by similar means.

During the second quarter of a turn, such of the carrying claws as have been allowed to recoil in the first, third, and fifth rows, are drawn up by the fingers on the axes of the adjacent dials; and, during the fourth quarter of a turn, such of the carrying claws on the second and fourth rows as have been allowed to recoil during the third quarter of a turn, are in like manner drawn up by the carrying fingers on the axes of the adjacent dials. It appears that the carriages proceed alternately from right to left along the horizontal rows during the second and fourth quarters of a turn; in the one, they pass along the first, third, and fifth rows, and in the other, along the second and fourth.

There are two systems of waves of mechanical action continually flowing from the bottom to the top; and two streams of similar action constantly passing from the right to the left. The crests of the first system of adding waves fall upon the last difference, and upon every alternate one proceeding upwards; while the crests of the other system touch upon the intermediate differences. The first stream of carrying action passes from right to left along the highest row and every alternate row, while the second stream passes along the intermediate rows.

Such is a very rapid and general outline of this machinery. Its wonders, however, are still greater in its details than even in its broader features. Although we despair of doing it justice by any description which can be attempted here, yet we should not fulfil the duty we owe to our readers, if we did not call their attention at least to a few of the instances of consummate skill which are scattered, with a prodigality characteristic of the highest order of inventive genius, throughout this astonishing mechanism.

In the general description which we have given of the mechanism for carrying, it will be observed, that the preparation for every carriage is stated to be made during the previous addition, by the disengagement of the carrying claw before mentioned, and by its consequent recoil, urged by the spiral spring with which it is connected; but it may, and does, frequently happen, that though the process of addition may not have rendered a carriage necessary, one carriage may itself produce the necessity for another. This is a contingency not provided against in the mechanism as we have described it: the case would occur in the scheme represented in fig. 1, if the figure under the index of C^2 were 4 instead of 3. The addition of the number 5 at the index of C^3 would, in this case, in the first quarter of a turn, bring 9 to the index of C^2: this would obviously render no carriage necessary, and of course no preparation would be made for one by the mechanism--that is to say, the carrying claw of the wheel D^2 would not be detached. Meanwhile a carriage upon C^2 has been rendered necessary by the addition made in the first quarter of a turn to B^2. This carriage takes place in the ordinary way, and would cause the dial C^2, in the second quarter of a turn, to advance from 9 to 0: this would make the necessary preparation for a carriage from C^2 to D^2. But unless some special arrangement was made for the purpose, that carriage would not take place during the second quarter of a turn. This peculiar contingency is provided against by an arrangement of singular mechanical beauty, and which, at the same time, answers another purpose--that of equalizing the resistance opposed to the moving power by the carrying mechanism. The fingers placed on the axes of the several dials in the row D^2, do not act at the same instant on the carrying claws adjacent to them; but they are so placed, that their action may be distributed throughout the second quarter of a turn in regular succession. Thus the finger on the axis of the dial A^2 first encounters the claw upon B^2, and drives it through one tooth immediately forwards; the finger on the axis of B^2 encounters the claw upon C^2 and drives it through one tooth; the action of the finger on C^2 on the claw on D^2 next succeeds, and so on. Thus, while the finger on B^2 acts on C^2, and causes the division from 9 to 0 to pass under the index, the thumb on C^2 at the same instant acts on the trigger, and detaches the carrying claw on D^2, which is forthwith encountered by the carrying finger on C^2, and driven forward one tooth. The dial D^2 accordingly moves forward one division, and 5 is brought under the index. This arrangement is beautifully effected by placing the several fingers, which act upon the carrying claws, spirally on their axes, so that they come into action in regular succession.

We have stated that, at the commencement of each revolution of the moving axis, the bolts which drive the dials of the first, third, and fifth rows, are shot. The process of shooting these bolts must therefore have taken place during the last quarter of the preceding revolution; but it is during that quarter of a turn that the carriages are effected in the second and fourth rows. Since the bolts which drive the dials of the first, third, and fifth rows, have no mechanical connexion with the dials in the second and fourth rows, there is nothing in the process of shooting those bolts incompatible with that of moving the dials of the second and fourth rows: hence these two processes may both take place during the same quarter of a turn. But in order to equalize the resistance to the moving power, the same expedient is here adopted as that already described in the process of carrying. The arms which shoot the bolts of each row of dials are arranged spirally, so as to act successively throughout the quarter of a turn. There is, however, a contingency which, under certain circumstances, would here produce a difficulty which must be provided against. It is possible, and in fact does sometimes happen, that the process of carrying causes a dial to move under the index from 0 to 1. In that case, the bolt, preparatory to the next addition, ought not to be shot until after the carriage takes place; for if the arm which shoots it passes its point of action before the carriage takes place, the bolt will be moved out of its sphere of action, and will not be shot, which, as we have already explained, must always happen when 0 is at the index: therefore no addition would in this case take place during the next quarter of a turn of the axis; whereas, since 1 is brought to the index by the carriage, which immediately succeeds the passage of the arm which ought to bolt, 1 should be added during the next quarter of a turn. It is plain, accordingly, that the mechanism should be so arranged, that the action of the arms, which shoot the bolts successively, should immediately follow the action of those fingers which raise the carrying claws successively; and therefore either a separate quarter of a turn should be appropriated to each of those movements, or if they be executed in the same quarter of a turn, the mechanism must be so constructed, that the arms which shoot the bolts successively, shall severally follow immediately after those which raise the carrying claws successively. The latter object is attained by a mechanical arrangement of singular felicity, and partaking of that elegance which characterises all the details of this mechanism. Both sets of arms are spirally arranged on their respective axes, so as to be carried through their period in the same quarter of a turn; but the one spiral is shifted a few degrees, in angular position, behind the other, so that each pair of corresponding arms succeed each other in the most regular order,--equalizing the resistance, economizing time, harmonizing the mechanism, and giving to the whole mechanical action the utmost practical perfection.

The system of mechanical contrivances by which the results, here attempted to be described, are attained, form only one order of expedients adopted in this machinery;--although such is the perfection of their action, that in any ordinary case they would be regarded as having attained the ends in view with an almost superfluous degree of precision. Considering, however, the immense importance of the purposes which the mechanism was destined to fulfil, its inventor determined that a higher order of expedients should be superinduced upon those already described; the purpose of which should be to obliterate all small errors or inequalities which might, even by remote possibility, arise, either from defects in the original formation of the mechanism, from inequality of wear, from casual strain or derangement,--or, in short, from any other cause whatever. Thus the movements of the first and principal parts of the mechanism were regarded by him merely as a first, though extremely nice approximation, upon which a system of small corrections was to be subsequently made by suitable and independent mechanism. This supplementary system of mechanism is so contrived, that if one or more of the moving parts of the mechanism of the first order be slightly out of their places, they will be forced to their exact position by the action of the mechanical expedients of the second order to which we now allude. If a more considerable derangement were produced by any accidental disturbance, the consequence would be that the supplementary mechanism would cause the whole system to become locked, so that not a wheel would be capable of moving; the impelling power would necessarily lose all its energy, and the machine would stop. The consequence of this exquisite arrangement is, that the machine will either calculate rightly, or not at all.

The supernumerary contrivances which we now allude to, being in a great degree unconnected with each other, and scattered through the machinery to a certain extent, independent of the mechanical arrangement of the principal parts, we find it difficult to convey any distinct notion of their nature or form.

In some instances they consist of a roller resting between certain curved surfaces, which has but one position of stable equilibrium, and that position the same, however the roller or the curved surfaces may wear. A slight error in the motion of the principal parts would make this roller for the moment rest on one of the curves; but, being constantly urged by a spring, it would press on the curved surface in such a manner as to force the moving piece on which that curved surface is formed, into such a position that the roller may rest between the two surfaces; that position being the one which the mechanism should have. A greater derangement would bring the roller to the crest of the curve, on which it would rest in instable equilibrium; and the machine would either become locked, or the roller would throw it as before into its true position.

In other instances a similar object is attained by a solid cone being pressed into a conical seat; the position of the axis of the cone and that of its seat being necessarily invariable, however the cone may wear: and the action of the cone upon the seat being such, that it cannot rest in any position except that in which the axis of the cone coincides with the axis of its seat.

Having thus attempted to convey a notion, however inadequate, of the calculating section of the machinery, we shall proceed to offer some explanation of the means whereby it is enabled, to print its calculations in such a manner as to preclude the possibility of error in any individual printed copy.

On the axle of each of the wheels which express the calculated number of the table T, there is fixed a solid piece of metal, formed into a curve, not unlike the wheel in a common clock, which is called the snail. This curved surface acts against the arm of a lever, so as to raise that arm to a higher or lower point according to the position of the dial with which the snail is connected. Without entering into a more minute description, it will be easily understood that the snail may be so formed that the arm of the lever shall be raised to ten different elevations, corresponding to the ten figures of the dial which may be brought under the index. The opposite arm of the lever here described puts in motion a solid arch, or sector, which carries ten punches: each punch bearing on its face a raised character of a figure, and the ten punches bearing the ten characters, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0. It will be apparent from what has been just stated, that this type sector (as it is called) will receive ten different attitudes, corresponding to the ten figures which may successively be brought under the index of the dial-plate. At a point over which the type sector is thus moved, and immediately under a point through which it plays, is placed a frame, in which is fixed a plate of copper. Immediately over a certain point through which the type sector moves, is likewise placed a bent lever, which, being straightened, is forcibly pressed upon the punch which has been brought under it. If the type sector be moved, so as to bring under the bent lever one of the steel punches above mentioned, and be held in that position for a certain time, the bent lever, being straightened, acts upon the steel punch, and drives it against the face of the copper beneath, and thus causes a sunken impression of the character upon the punch to be left upon the copper. If the copper be now shifted slightly in its position, and the type sector be also shifted so as to bring another punch under the bent lever, another character may be engraved on the copper by straightening the bent lever, and pressing it on the punch as before. It will be evident, that if the copper was shifted from right to left through a space equal to two figures of a number, and, at the same time, the type sector so shifted as to bring the punches corresponding to the figures of the number successively under the bent lever, an engraved impression of the number might thus be obtained upon the copper by the continued action of the bent lever. If, when one line of figures is thus obtained, a provision be made to shift the copper in a direction at right angles to its former motion, through a space equal to the distance between two lines of figures, and at the same time to shift it through a space in the other direction equal to the length of an entire line, it will be evident that another line of figures might be printed below the first in the same manner.

The motion of the type sector, here described, is accomplished by the action of the snail upon the lever already mentioned. In the case where the number calculated is that expressed in fig. 1, the process would be as follows:--The snail of the wheel F^1, acting upon the lever, would throw the type sector into such an attitude, that the punch bearing the character 0 would come under the bent lever. The next turn of the moving axis would cause the bent lever to press on the tail of the punch, and the character 0 would be impressed upon the copper. The bent lever being again drawn up, the punch would recoil from the copper by the action of a spring; the next turn of the moving axis would shift the copper through the interval between two figures, so as to bring the point destined to be impressed with the next figure under the bent lever. At the same time, the snail of the wheel E would cause the type sector to be thrown into the same attitude as before, and the punch would be brought under the bent lever; the next turn would impress the figure beside the former one, as before described. The snail upon the wheel D would now come into action, and throw the type sector into that position in which the punch bearing the character 7 would come under the bent lever, and at the same time the copper would be shifted through the interval between two figures; the straightening of the lever would next follow, and the character 7 would be engraved. In the same manner, the wheels C, B, and A would successively act by means of their snails; and the copper being shifted, and the lever allowed to act, the number 007776 would be finally engraved upon the copper: this being accomplished, the calculating machinery would next be called into action, and another calculation would be made, producing the next number of the Table exhibited in fig. 5. During this process the machinery would be engaged in shifting the copper both in the direction of its length and its breadth, with a view to commence the printing of another line; and this change of position would be accomplished at the moment when the next calculation would be completed: the printing of the next number would go on like the former, and the operation of the machine would proceed in the same manner, calculating and printing alternately. It is not, however, at all necessary--though we have here supposed it, for the sake of simplifying the explanation--that the calculating part of the mechanism should have its action suspended while the printing part is in operation, or vice versa; it is not intended, in fact, to be so suspended in the actual machinery. The same turn of the axis by which one number is printed, executes a part of the movements necessary for the succeeding calculation; so that the whole mechanism will be simultaneously and continuously in action.

Of the mechanism by which the position of the copper is shifted from figure to figure, from line to line, we shall not attempt any description. We feel that it would be quite vain. Complicated and difficult to describe as every other part of this machinery is, the mechanism for moving the copper is such as it would be quite impossible to render at all intelligible, without numerous illustrative drawings.

The engraved plate of copper obtained in the manner above described, is designed to be used as a mould from which a stereotyped plate may be cast; or, if deemed advisable, it may be used as the immediate means of printing. In the one case we should produce a table, printed from type, in the same manner as common letter-press printing; in the other an engraved table. If it be thought most advisable to print from the stereotyped plates, then as many stereotyped plates as may be required may be taken from the copper mould; so that when once a table has been calculated and engraved by the machinery, the whole world may be supplied with stereotyped plates to print it, and may continue to be so supplied for an unlimited period of time. There is no practical limit to the number of stereotyped plates which may be taken from the engraved copper; and there is scarcely any limit to the number of printed copies which may be taken from any single stereotyped plate. Not only, therefore, is the numerical table by these means engraved and stereotyped with infallible accuracy, but such stereotyped plates are producible in unbounded quantity. Each plate, when produced, becomes itself the means of producing printed copies of the table, in accuracy perfect, and in number without limit.

Unlike all other machinery, the calculating mechanism produces, not the object of consumption, but the machinery by which that object may be made. To say that it computes and prints with infallible accuracy, is to understate its merits:--it computes and fabricates the means of printing with absolute correctness and in unlimited abundance.

For the sake of clearness, and to render ourselves more easily intelligible to the general reader, we have in the preceding explanation thrown the mechanism into an arrangement somewhat different from that which is really adopted. The dials expressing the numbers of the tables of the successive differences are not placed, as we have supposed them, in horizontal rows, and read from right to left, in the ordinary way; they are, on the contrary, placed vertically, one below the other, and read from top to bottom. The number of the table occupies the first vertical column on the right, the units being expressed on the lowest dial, and the tens on the next above that, and so on. The first difference occupies the next vertical column on the left; and the numbers of the succeeding differences occupy vertical columns, proceeding regularly to the left; the constant difference being on the last vertical column. It is intended in the machine now in progress to introduce six orders of differences, so that there will be seven columns of dials; it is also intended that the calculations shall extend to eighteen places of figures: thus each column will have eighteen dials. We have referred to the dials as if they were inscribed upon the faces of wheels, whose axes are horizontal and planes vertical. In the actual machinery the axes are vertical and the planes horizontal, so that the edges of the figure wheels, as they are called, are presented to the eye. The figures are inscribed, not upon the dial-plate, but around the surface of a small cylinder or barrel, placed upon the axis of the figure wheel, which revolves with it; so that as the figure wheel revolves, the figures on the barrel are successively brought to the front, and pass under an index engraved upon a plate of metal immediately above the barrel. This arrangement has the obvious practical advantage, that, instead of each figure wheel having a separate axis, all the figure wheels of the same vertical column revolve on the same axis; and the same observation will apply to all the wheels with which the figure wheels are in mechanical connexion. This arrangement has the further mechanical advantage over that which has been assumed for the purposes of explanation, that the friction of the wheel-work on the axes is less in amount, and more uniformly distributed, than it could be if the axes were placed in the horizontal position.

A notion may therefore be formed of the front elevation of the calculating part of the mechanism, by conceiving seven steel axes erected, one beside another, on each of which shall be placed eighteen wheels, five inches in diameter, having cylinders or barrels upon them an inch and a half in height, and inscribed, as already stated, with the ten arithmetical characters. The entire elevation of the machinery would occupy a space measuring ten feet broad, ten feet high, and five feet deep. The process of calculation would be observed by the alternate motion of the figure wheels on the several axes. During the first quarter of a turn, the wheels on the first, third, and fifth axes would turn, receiving their addition from the second, fourth, and sixth; during the second quarter of a turn, such of the wheels on the first, third, and fifth axes, to which carriages are due, would be moved forward one additional figure; the second, fourth, and sixth columns of wheels being all this time quiescent. During the third quarter of a turn, the second, fourth, and sixth columns would be observed to move, receiving their additions from the third, fifth, and seventh axes; and during the fourth quarter of a turn, such of these wheels to which carriages are due, would be observed to move forward one additional figure; the wheels of the first, third, and fifth columns being quiescent during this time.

It will be observed that the wheels of the seventh column are always quiescent in this process; and it may be asked, of what use they are, and whether some mechanism of a fixed nature would not serve the same purpose? It must, however, be remembered, that for different tables there will be different constant differences; and that when the calculation of a table is about to commence, the wheels on the seventh axis must be moved by the hand, so as to express the constant difference, whatever it may be. In tables, also, which have not a difference rigorously constant, it will be necessary, after a certain number of calculations, to change the constant difference by the hand; and in this case the wheels of the seventh axis must be moved when occasion requires. Such adjustment, however, will only be necessary at very distant intervals, and after a considerable extent of printing and calculation has taken place; and when it is necessary, a provision is made in the machinery by which notice will be given by the sounding of a bell, so that the machine may not run beyond the extent of its powers of calculation.

Immediately behind the seven axes on which the figure wheels revolve, are seven other axes; on which are placed, first, the wheels already described as driven by the figure wheels, and which bear upon them the wedge which withdraws the bolt immediately over these latter wheels, and on the same axis is placed the adding bolt. From the bottom of this bolt there projects downwards the pin, which acts upon the unbolting wedge by which the bolt is withdrawn: from the upper surface of the bolt proceeds a tooth, which, when the bolt is shot, enters between the teeth of the adding wheel, which turns on the same axis, and is placed immediately above the bolt: its teeth, on which the bolt acts, are like the teeth of a crown wheel, and are presented downwards. The bolt is fixed upon this axis, and turns with it; but the adding wheel above the bolt, and the unbolting wheel below it, both turn upon the axis, and independently of it. When the axis is made to revolve by the moving power, the bolt revolves with it; and so long as the tooth of the bolt remains inserted between those of the adding wheel, the latter is likewise moved; but when the lower pin of the bolt encounters the unbolting wedge on the lower wheel, the tooth of the bolt is withdrawn, and the motion of the adding wheel is stopped. This adding wheel is furnished with spur teeth, besides the crown teeth just mentioned; and these spur teeth are engaged with those of that unbolting wheel which is in connexion with the adjacent figure wheel to which the addition is to be made. By such an arrangement it is evident that the revolution of the bolt will necessarily add to the adjacent figure wheel the requisite number.