Part 3

Positions of Known Nebulæ Determined from the Crossley Negatives, " 42

List of Illustrations, " 45

Illustrations, following " 46

THE CROSSLEY REFLECTOR OF THE LICK OBSERVATORY.

By JAMES E. KEELER.

The Crossley reflector, at present the largest instrument of its class in America, was made in 1879 by Dr. A. A. Common, of London, in order to carry out, and test by practical observation, certain ideas of his respecting the design of large reflecting telescopes. For the construction of the instrument embodying these ideas, and for some fine astronomical photographs obtained with it, Dr. Common was awarded the gold medal of the Royal Astronomical Society in 1884.

In 1885, Dr. Common, wishing to make a larger telescope on a somewhat similar plan, sold the instrument to Edward Crossley, Esq., F. R. A. S., of Halifax, England. Mr. Crossley provided the telescope with a dome of the usual form, in place of the sliding roof used by its former owner, and made observations with it for some years; but the climate of Halifax not being suitable for the best use of such a telescope, he consented, at the request of Dr. Holden, then Director of the Lick Observatory, to present it to this institution. The funds for transporting the telescope and dome to California, and setting them up on Mount Hamilton, were subscribed by friends of the Lick Observatory, for the most part citizens of California. The work was completed, and the telescope housed in a suitable observatory building, in 1895.

On taking charge of the Lick Observatory in 1898, I decided to devote my own observing time to the Crossley reflector, although the whole of my previous experience had been with refracting telescopes. I was more particularly desirous of testing the reflector with my own hands, because such preliminary trials of it as had been made had given rise to somewhat conflicting opinions as to its merits. The result of my experience is given in the following article, which is written chiefly with reference to American readers. If I have taken occasion to point out what I regard as defects in the design or construction of the instrument, I have done so, not from any desire to look a gift horse in the mouth, but in the interest of future improvement, and to make intelligible the circumstances under which the work of the reflector is now being done and will be done hereafter. The most important improvements which have suggested themselves have indeed already been made by Dr. Common himself, in constructing his five-foot telescope. The three-foot reflector is, in spite of numerous idiosyncracies which make its management very different from the comparatively simple manipulation of a refractor, by far the most effective instrument in the Observatory for certain classes of astronomical work. Certainly no one has more reason than I to appreciate the great value of Mr. Crossley's generous gift.

The Crossley dome is about 350 yards from the main Observatory, at the end of a long rocky spur which extends from the Observatory summit toward the south, and on which are two of the houses occupied by members of the Observatory staff. It is below the level of the lowest reservoir, "Huyghens," which receives the discharge from the hydraulic machinery of the 36-inch refractor, and therefore the water engine furnished by Mr. Crossley for turning the dome can not be used, unless a new water system--overflow reservoir, pump and windmill--is provided. In this respect a better site would have been a point on the south slope of "Kepler,"--the middle peak of Mount Hamilton--just above the Huyghens reservoir. No addition to the present water system would then have been needed. The slope of the mountain at this place might cut off the view of the north horizon, but since the telescope can not be turned below the pole, this would be a matter of no consequence. Water-power for the dome is not, however, really necessary.

The cylindrical walls of the dome, 36-1/4 feet inside diameter, are double, and provided with ventilators. Opening into the dome, on the left of the entrance, are three small rooms, one of which has been fitted up as a photographic dark room, and another, containing a sidereal clock and a telephone, which communicates with the main Observatory, as a study, while the third is used for tools and storage. There is also a small room for the water engine, in case it should be used. The dome is at present supplied with water from only the middle reservoir, Kepler, which is reserved for domestic purposes and is not allowed to pass through the machinery.

The dome itself, 38 feet 9 inches in diameter, is made of sheet-iron plates riveted to iron girders. It also carries the wooden gallery, ladders, and observing platform, which are suspended from it by iron rods. The apparatus for turning the dome consists of a cast-iron circular rack bolted to the lower side of the sole-plate, and a set of gears terminating in a sprocket-wheel, from which hangs an endless rope. As the dome does not turn easily, it has been necessary to multiply the gearing of the mechanism so that one arm's-length pull on the rope moves the dome only about one inch. In some positions of the telescope the dome can not be moved more than six or eight inches at a time without danger of striking the tube, and this slowness of motion is then not disadvantageous. It is only when the dome has to be moved through a considerable angle, as in turning to a fresh object, or in photographing some object which passes nearly through the zenith, that the need for a mechanical means of rotation is felt.

The observing slit, 6 feet wide, extends considerably beyond the zenith. It is closed by a double shutter, which is operated by an endless rope. The upper part, within the dome, is also closed by a hood, or shield, which serves to protect the telescope from any water that may find its way through the shutter, and which is rolled back to the north when observations are made near the zenith. I have recently fitted the lower half of the slit with a wind-screen, which has proved to be a most useful addition. It is made of tarpaulin, attached to slats which slide between the two main girders, and is raised or lowered by halliards, which belay to cleats on the north rail of the gallery. A more detailed description of the dome has been given in an article by Mr. Crossley, from which the reduced figure in Fig. 1 has been taken.

The mounting of the three-foot reflector has been very completely described and illustrated by Dr. Common, so that only a very general description need be given here. The most important feature of the mounting is that the telescope tube, instead of being on one side of the polar axis, as in the usual construction, is central, so that the axis of the mirror and the polar axis are in the same line when the telescope is directed to the pole. The declination axis is short, and is supported by a massive goose-neck bolted to the upper end of the polar axis. The mirror is placed just above the declination axis. Its weight, and the weight of the whole tube and eye-end, are counterpoised by slabs of lead, placed in two iron boxes, between which the goose-neck of the polar axis passes. The great advantage of this arrangement, and the controlling principle of the design, is that the telescope is perfectly free to pass the meridian at all zenith distances. No reversal of the instrument is needed, or is indeed possible.

For long-exposure photography, the advantage above referred to is obvious, but it is attended by certain disadvantages. One of these is that a very much larger dome is required than for the usual form of mounting. Another is the great amount of dead weight which the axes must carry; for the mirror, instead of helping to counterpoise the upper end of the tube, must itself be counterpoised. When anything is attached to the eye-end (and in astrophysical work one is always attaching things to the eye-end of a telescope), from ten to twenty times as much weight must be placed in the counterpoise boxes below the declination axis. Where room is to be found for the weights required to counterpoise the Bruce spectrograph, is a problem which I have not yet succeeded in solving.

In his five-foot reflector, Dr. Common has caused the telescope tube to swing between two large ears, which project from the upper end of the boiler-like polar axis, the pivots constituting the declination axis being near, but above, the lower end of the tube. The mirror, therefore, helps to counterpoise the upper end of the tube. This I regard as a distinct improvement. The danger of large masses of metal near the mirror injuring the definition is, in my opinion, imaginary; at least there is no such danger on Mount Hamilton, where the temperature variations are unusually small. Experience with the Crossley reflector, as well as with the other instruments of the Lick Observatory, shows that the definition depends almost entirely on external conditions.

My first trials of the reflector, as first mounted at the Lick Observatory, showed that the center of motion was inconveniently high. Among other difficulties arising from this circumstance, the spectroscope projected beyond the top of the dome, so that it had to be removed before the shutter could be closed. In July, 1898, the pier was therefore cut down two feet. This brought the eye-end down nearly to the level of the gallery rail, where it was at a convenient height for the observer when sitting on a camp-stool, and it made all parts of the mounting more accessible. Toward the north and south, the range of the telescope, being limited in these directions by the construction of the mounting, was not affected by the change, but the telescope can not now be used at such low altitudes as formerly, near the east and west points of the horizon. The only occasion likely to call for the use of the reflector in these positions is the appearance of a large comet near the Sun, and, after some consideration, I decided to sacrifice these chances for the sake of increasing the general usefulness of the instrument. Except in rare cases, all observations are made within three hours of the meridian.

To adapt the mounting to the latitude of Mount Hamilton, a wedge-shaped casting, shown in the illustration, had been provided, but through some error, arising probably from the fact that the telescope had been used in two different latitudes in England, the angle of the casting was too great. When the pier was cut down its upper surface was therefore sloped toward the south, in order to compensate the error in the casting. Plate VII shows the instrument very nearly as it is at the present time.

The polar axis of the Crossley reflector is a long, hollow cylinder, separated by a space of about one-eighth of an inch from its concentric casing. The idea was to fill this space with mercury, and float the greater part of the thrust of the axis, the function of a small steel pin at the lower end being merely to steady the axis. But this mercury flotation, as applied to the Crossley telescope, is a delusion, as I think Mr. Crossley had already found. The mercury, it is true, relieves the thrust to some extent, but it greatly increases the already enormous side pressure on the steel pin at the bottom, thus creating a much greater evil than the one it is intended to remedy. The workmen who set up the mounting inform me that the small bearing at the lower end of the polar axis is badly worn, as I should expect it to be. Instead of putting mercury into the space intended for it, I have therefore poured in a pint or so of oil, to keep the lower bearing lubricated. For the reasons indicated above, the force required to move the telescope in right ascension is perhaps five times greater than it should be. The lower end of the polar axis ought to be fitted with ball bearings to take the thrust, and with a pair of friction wheels on top; but it would be difficult to make these changes now. It should be observed that the disadvantages of the mercury flotation are considerably greater at Mount Hamilton than at the latitude for which the telescope was designed.

As already stated above, the range of the telescope is limited on the south by the construction of the mounting. The greatest southern declination which can be observed is 25°. In England this would doubtless mark the limit set by atmospheric conditions, but at Mount Hamilton it would be easy to photograph objects 15° farther south, if the telescope could be pointed to them.

The original driving-clock having proved to be inefficient, at least without an electric control, a new and powerful driving-clock was made by the Observatory instrument maker, from designs by Professor Hussey. In its general plan it is like that of the 36-inch refractor. The winding apparatus, contained in the large casting of the original mounting, has no maintaining power, and can not easily be fitted with one. The clock could in no case be wound during a photographic exposure, on account of the tremors attending the operation, but it would be somewhat more convenient to have the stars remain on the plate during the winding. With a little practice, however, one can wind the clock without actually stopping it, though the object must afterwards be brought back to its place by means of the slow motion in right ascension.

Two finders have recently been fitted to the Crossley reflector. One has an object-glass of four inches aperture and eight feet six inches focal length, with a field of about 1° 2´, which is very nearly the photographic field of the main telescope. Its standards are bolted to one of the corner tubes of the reflector. The other finder has a three-inch objective and a large field. It had not been mounted when the photograph for the plate was made.

When a telescope is used for photographing objects near the pole, with long exposures, the polar axis must be quite accurately adjusted, for otherwise the centers of motion of the stars and of the telescope will not agree, and the star images will be distorted. It is true that with a double-slide plate-holder, like the one used with the Crossley reflector, one star--namely, the guiding star--is forced to remain in a fixed position with respect to the plate; but the differential motion of the other stars causes them to describe short arcs, or trails, around this star as a center. A considerable part of the spring of 1899 was spent in efforts to perfect the adjustment of the polar axis, an operation which, on account of the peculiar form of the mounting, offers unusual difficulties.

In the first plan which was tried, the reflector was used as a transit instrument. The inclination of the declination axis was determined with a hanging level which had been provided by Mr. Crossley, the hour circle and polar axis being very firmly clamped. The clock correction being known from the records kept at the Observatory, the collimation and azimuth constants were found by the usual formulæ. This method failed to give satisfactory results, and it was found later that the declination and polar axis were not exactly at right angles.

There is only one part of the sky on which the telescope can be reversed; namely, the pole. A method which promised well, and on which some time was spent, consists in photographing the pole (the declination axis being horizontal) by allowing the stars near it to trail for ten or fifteen minutes, then turning the polar axis 180° and photographing the pole again on the same plate. Half the distance between the images gives the error of the polar axis, which, if the plate is properly oriented, is easily resolved into horizontal and vertical components; while the distance of each image from the center of the plate is this error increased or diminished by twice the deviation of the telescope axis. In this case the vertical component depends upon the reading of the declination circle, and the horizontal component gives the error of collimation. This method failed, however, to give consistent results, mainly on account of instability of the mirror, and was abandoned.

The use of the large mirror for purposes of adjustment was finally given up, and the axis was adjusted by observations of Polaris with the long finder, in the usual manner. In order to reach the star at lower culmination the finder tube had to be thrown out of parallelism with the main telescope.

The base-plate having no definite center of rotation in azimuth, and the wedges and crowbars used for moving it being uncertain in their action, a watch telescope, provided with a micrometer eyepiece, was firmly secured to the mounting throughout these operations, in such manner that a mark on the southern horizon could be observed through one of the windows of the dome. The errors of the polar axis were finally reduced to within the limits of error of observation.

The movable hour circle and driving wheel of the Crossley reflector has two sets of graduations. The driving screw having been thrown out of gear, the circle is turned until the outer vernier indicates the sidereal time, whereupon the driving screw is thrown into gear again. The inner vernier is then set to the right ascension of the object which it is desired to observe. As an inconsistency, of minor importance, in the design of the mounting, I may note that the slow motion in right ascension changes the reading of the outer vernier instead of that of the inner one. In practice, however, no inconvenience is caused by this construction.

In the early experiments and photographic work with the Crossley telescope, irregularities in driving were a source of great annoyance. Dr. Roberts, in laying down the conditions which should be fulfilled by a good photographic telescope, says that a star should remain bisected by a thread in the eyepiece for two minutes at a time. The Crossley telescope was so far from fulfilling this condition that a star would not keep its place for two consecutive seconds; and the greatest alertness on the part of the observer did not suffice to ensure round star images on a photographic plate. It was obvious that the fault did not lie with the driving clock; in fact, many of the sudden jumps in right ascension, if explained in this way, would have required the clock to run backward; nevertheless the clock was tested by causing its revolutions to be recorded on a chronograph at the main Observatory, together with the beats of one of the standard clocks. For this purpose a break-circuit attachment was made by Mr. Palmer. The errors of the clock were in this way found to be quite small.