Part 66

Some, instead of these Sheats, make use of hollow wooden Harrow-tines, thro’ which the Seed descends: But these I do not approve of; because where the Ground is hard, and not fine, they rise up, and make no Chanels for the Seed; and then it lying uncover’d will be malted.

When a Drill has only one Rank of Shares, we screw on the Harrow by its Legs, to the Inside of the Two outside Sheats, as near as we can to their fore Shoulders, leaving sufficient room for the Harrow to rise and sink, in the same manner as when it is drawn by the Beams.

Page. 378

B. Cole Sculps.]

CHAP. XXII.

Of the Turnep-Drill.

Plate 5. shews the whole Mounting of a Turnep-drill. Fig. 1. is a Plough, but little differing from the Drill-plough last mentioned. A, A, are the Two Limbers, differing in nothing from the other, except that they are lighter, not being above Two Inches Diameter, behind the Bar: They are drawn in the same manner as the other. Their Bar B is distant from the Plank Three Inches, being shoulder’d at each End, with a very thin flat Tenon, passing thro’ each Limber, and pinn’d on their Outsides, as at a a. We do not pin in this Bar thro’ the Limbers, lest the Holes should make these very small Limbers the weaker in that Part. C, the Plank, Two Feet and an Inch long, Five Inches broad, and an Inch and a quarter thick. D, D, the Two double Standards, or Two Pair of Standards, placed into the Plank with Shoulders above, and Tenons pinn’d underneath the Plank, and are Thirteen Inches high above it: These serve for a Pair of Marking-wheels, when Turneps are drill’d on the Level, to keep the Rows all parallel, and at what Distance you please, by setting them according to the Rule already laid down.

Sometimes we place the double Standards into the Plank of the Wheat-drill, in the same manner that these are placed.

We take off the inner Edge of each Standard at the Top, as at b b and b b, for the more easy Admission of the Spindle of the Marking-wheels into the Forks: This Spindle is kept in its Place by Two of the same sort of Wreaths, and placed in the same manner as those describ’d for the fore Hopper of the Wheat-drill.

Such Marking-wheels are necessary for drilling upon the Level; but not for drilling upon Ridges.

E is the Beam, Two Feet Two Inches and an half long, Four Inches broad, and Two Inches thick: It is thus broad, that the Screws which hold on the cross Piece F, may be farther asunder: The Screws must be placed as near as may be to the Outsides of the Beam, and at equal Distance from each Side of the cross Piece; by which means the Standards are kept the firmer from Turning.

The Distance between the Plank and the cross Piece is Eleven Inches. The Breadth of the cross Piece is Two Inches and a quarter. This cross Piece is shewn apart in Fig. 2. where its Two Standards A B, are each Seventeen Inches long (or high), and each on its fore Side and hinder Side One Inch and a quarter broad, and nearly Three quarters of an Inch thick: They are shoulder’d and pinn’d into the cross Piece at a b. The cross Piece is Thirteen Inches and an half long, and one Inch and a quarter thick in the Middle from c to d; but for about an Inch on the Inside of each Standard is Two Inches and an half thick, that the Standards may have the more Wood to support them, and that the Hopper, bearing upon the thicker Parts of the cross Piece, may be held up above the Funnel, that the Fork of the brass Spindle may not strike against it, when the Plough is taken up to be turn’d, there being a little more than a quarter of an Inch of the Breadth of the cross Piece behind the Standard, for the Hopper to rest on.

The whole Distance between the Standards is Nine Inches and a quarter. The Standards must be exactly perpendicular to their cross Piece: Their Tops are drawn up each to a Point, as at e and f, by which the Hopper is the more easily put on upon them.

The Funnel, Sheat, Share, and Trunk, are the same as those in the Wheat-drill, except a few Differences: As G in Fig. 1. is the same as the fore Sheat of the Wheat-drill, with its Accoutrements; only it is lower, being but Eight Inches high from the Bottom of the Share up to the Beam; and the Plates of the Trunk are somewhat narrower: Its Tenon passes thro’ the Beam, and comes up above it, betwixt the Funnel and the cross Piece; and there is pinn’d in thro’ its Hole above the Beam. There is no want of Wood behind the Sheat, the Funnel not being cut in the Beam, but placed upon it.

The Funnel is shewn apart in Fig. 3. and is Two Inches deep, Four Inches square at Top; its Four Sides terminating at an Hole in the Bottom, half an Inch broad from a to b, and near an Inch long from c to d, which Length is divided in the Middle, by the upper Edge of a Brass Spout, which divides the Hole into Two equal Parts (or Holes), each of which is about half an Inch square; this Funnel being screw’d on upon the Beam by Two Wood Screws, entering at Two opposite Corners of the Funnel, as at c d in Fig. 1. so that the Seed may drop from the Seed-box upon the right Side of the Funnel at e, which being about half an Inch distant from the Partition, and equidistant from both Holes, the Seed rebounding is pretty equally distributed to each of the Holes.

The fore Part of the foremost Hole being equal with the Back of the Sheat, the Beam being cut thro’; so that the Back of the Sheat, and the fore Part of the Hole thro’ the Beam, and the fore Part of this Hole, make one plain Surface, whereby the Seed that falls into this foremost Hole, descends to the Ground, near the Back of the Sheat, thro’ the Trunk.

And the Seed which falls into the hinder Hole, is convey’d obliquely backwards thro’ Part of the Beam, by a short thin Brass Spout, whose Diameter in the Inside is somewhat more than half an Inch; but the fore Part of it, which divides the Two Holes, descends first perpendicularly half an Inch, and then turns off backwards, and there the Spout begins to be round: Its joining is on its hinder Part, to the end that the Seed, never running upon it, cannot be stopp’d by it. The lower End of this Spout ends at the lower Surface of the Beam, a little behind the Plates of the Trunk, which Hole is seen at a in Fig. 4. where this Hole delivers the Seed down into the Spout A, when it is drawn up into its Place by the String B drawn thro’ the Hole at b in the End of the Beam, and there tied until it stand in the Posture in which it is seen at f in Fig. 1.

The Shape of this Spout is better seen at Fig. 5. where A is the Spout, Four Inches long, a full Inch Diameter in the Inside: Its lower End is circular; but its upper End B is cut at oblique Angles, so that when it is drawn up to its Place, its Edges will touch the lower Surface of the Beam, and inclose the lower End of the other Spout within it: It is made of thin hammer’d Brass (as is the other). The Edges of the Piece of Brass, which make this Spout, are join’d on its hinder Part, for the same Reason that they are so in the other Spout. At b there is a Jag cut in one of these Edges, and rais’d upwards, by which Jag the String being tied on the Spout just below, is hindered from slipping upwards.

Joining to the highest Part, and made with Part of the same Piece of Brass, turn’d back from the End of the Spout, is its Hinge C, near Three quarters of an Inch long in its Hollow.

D is a thin Piece of Iron, half an Inch broad, and a little longer than the Top of the Sheat, by which the Spout is held up: This Piece of Iron is riveted by a Rivet passing thro’ an Hole at c, and thro’ the Sheat, just before the Trunk, and thro’ another Piece of Iron on the opposite Side; both the Pieces of Iron, with their upper Edges touching the Beam, being thus riveted to the Sheat.

The Spout is pinned in by the Screw E, passing as by the prick’d Line F thro’ the Hole G, and also thro’ the Hinge C, and screw’d into the Hole of the opposite Piece of Iron, corresponding with the Hole G; and then it will appear as in Fig. 4.

Instead of these Pieces of Iron, we sometimes use Pieces of Wood, a little broader and thicker, nail’d on the Sheat.

The Use of this Spout is for carrying half of the Seed backwards, so that it may drop upon the Chanel, after the Earth is fallen into it: By this means the Seed lying very shallow, being only cover’d by a little Earth rais’d by the Harrow, by its Shallowness comes up in moist Weather, sooner than the other half, which lies deeper in the Ground; but if the Weather be dry when planted, the deeper half, by the Moisture of the Earth from the Dews, will come up first, and the shallow half will not come up till Rain come to moisten it; so that by the shallow or deep, the Turnep-fly is generally disappointed.

Fig. 6. shews one of the Tines of a Drill-harrow made of Wood: Its Edge a b is made roundish at b, by which means it raises the Earth on its Sides; but does not drive it before: This Edge from a to b is Six Inches long; from b to c, being its Bottom, is One Inch and a quarter; from c to d is the Back, an Inch and an half thick at Top, gradually tapering downwards to c, where it is half an Inch thick, being shoulder’d all round: It has a flat Tenon A, which passes thro’ a Mortise in the Harrow-head; the Length of which Mortise is parallel with the Length of the Harrow-head, into which it is held by a Pin, passing thro’ the Hole of the Tenon, above the Harrow; as may be seen in Fig. 7. at a; and its Fellow at b.

These Two Tines are Eight Inches asunder at their Points, and Six Inches and a quarter asunder at their upper Parts, just under the Harrow-head. The fore Edge of the Tine A inclines a little to the Left, as the Edge of the Tine B doth to the Right.

Fig. 8. shews one of the Legs of the Harrow. At a is seen the round Tenon, which passes thro’ the Harrow-head up to its Shoulder, and is pinned in thro’ an Hole of the Tenon just behind the Harrow-head; upon this Tenon the Harrow-head may turn: The other End has an Hole at b, thro’ which it is pinned on to the Beam. The Length of the Leg from the Shoulder at a, to the Hole at b, is Twenty Inches: Its Thickness is an Inch and a quarter, and its Breadth an Inch. The Two Legs are seen mark’d C, D, in Fig. 7. They bend down in the Middle, to give the Harrow the more room for rising and sinking; they are parallel to each other, and distant a little more than the Breadth of the Beam, that they may have Liberty to move thereon, when one End of the Harrow-head sinks lower than the other, by the Unevenness of the Ground.

The Harrow is pinned on to the Beam by the Iron Pin, Fig. 9. passing thro’ the Hole of the Leg at g, and thro’ the Beam, and also thro’ the other Leg on the other Side of the Beam, where the Screw at the End of the Pin has a Nut screw’d on it. This Pin is round from its Head all the Way thro’ the first Harrow-leg, and thro’ the Beam; but all that Part of the Pin, which is in that Leg against which the Nut is screw’d, must be square; whereby that Part being bigger than the round Part of the Pin, and than the Hole in the last-mention’d Leg, cannot turn in the Hole of that Leg; for if it did, the Nut would be soon unscrew’d by the Motion of the Harrow; but the Pin must have room to turn in the other Leg, and in the Beam. This square Part of the Pin is seen at a, Fig. 9. The whole Length of the Pin, from its Head to the End of the square Part at a, where the Screw begins, is of the Thickness of the Two Legs, and of the Breadth of the Beam.

We sometimes set the Legs of the Harrow Two Inches wider asunder, by making them each an Inch thicker at their fore Ends in their Inside, and reaching Five or Six Inches behind their Iron Pin: These thicker Parts, bearing against the Beam, keep the hinder Part of each Harrow-leg an Inch distant from the Sides of the Beam, whereby the Harrow-legs are Six Inches asunder, instead of Four, by means of these added Thicknesses.