Part 63

The Shares must be all of them parallel to the Beams, and consequently to one another.

The Chanel made by the fore Share and Sheat for the middle Row, being at equal Distance between the Two hinder Sheats, is cover’d by them, they raising the Mould over the Seed from each Side of this Chanel.

The Harrow I is drawn by the Beams, to which it is fastened to their Insides at d and e, having each a small Iron Pin, passing thro’ each End of the Legs of the Harrow, and thro’ the Beams; each having a Nut on the Outsides of the Beams, and being square in the Beams, that they may not turn therein to loosen their Nuts; but are round near their Heads, that the Harrow may easily move thereon.

The round Ends of the Legs of the Harrow are put thro’ its Head I, at the round Holes f and g; and pinned in behind it, to the end that either Tine of the Harrow may descend at the same time that the other rises, where the Ground is uneven.

The Two wooden Tines K and L are pinned in above the Head, and have each of them a Shoulder underneath. They stand sloping; so that if they take hold of any Clods, they do not drive them before them, but rise over them. They are of a convenient Length, to give room for the Harrow to sink and rise, without raising up the Shares; and to give them the more room to move: The Legs of the Harrow are crook’d downwards in the Middle.

The Distance of these Tines from each other is Twenty-two Inches; so that each Tine going Three Inches and an half on the Outside of each Chanel that is next it, fills it up with Earth upon the Seed, from the Outsides of it; which causes the Rows to come up something nearer the inner Sides of the Chanels, than to the outer Sides, from whence the Earth is brought into them by the Tines; and the Two outer Rows by this means come up at Fourteen Inches asunder, tho’ the Chanels were Fifteen Inches asunder.

This way of covering adds more Mould to the Top of a Ridge; whereas, if the Chanels were covered by Tines going within or between them, the Mould would be thrown down from the Top of the Ridge: And these Tines stand with their Edges and Points inclining outwards, by which means they bring in the more Earth to the Chanels.

If we find, that the Harrow is too light, we tie a Stone upon it, to make it heavier; and sometimes we fix a small Box of Board on the Middle of it, to hold Clods of Earth for that Purpose.

The fore Funnel C has its upper Edges Two Inches high above the Surface of the Plank. It is Five Inches Square at Top; its Four opposite Sides being Planes equally inclin’d to each other downwards, until they end at the Hole in the Bottom of the Funnel, which Hole is continued quite thro’ the Plank into the Trunk. The Shape of this Hole is shewn in Fig. 9. where the Four Lines a b, b c, c d, and d a, each Line being Three quarters of an Inch, make a true Square, and are the upper Edges of the Hole. The Three prick’d Lines e f, f g, and g h, being each of them longer than the former, tho’ as little as possible, make the Three lower Edges of the Hole; which being thus wider below than above, and having all its Sides true Planes and smooth, it is impossible for the Seed to arch therein. The fore Side of this Hole is perpendicular to the upper and lower Surfaces of the Plank, and, together with the Back of the Sheat, makes one Plane Surface.

When we drill a large Species of Seed, as Peas or Oats, we can make this Hole a full Inch square at Top, and of the same Shape wider at Bottom; which tho’ it be wider than the Trunk, except at its Top, the Seed will not arch there, because there is room behind, the Plates being broader than the Sides of the Hole; for there can be no Arching in the Trunk, unless the Seed were confin’d behind as well as on each Side.

The Holes of our Funnels ought to be of the same Shape with this described; tho’, as I am inform’d, the Pretenders to the making of this Plough make the Holes of their Funnels the Reverse of this; which being wrong-way upwards, the Seed is apt to arch in them, except the Holes are very large.

Of this Plough, Fig. 1. the Two hinder Funnels E and F differ from the fore Funnel (which has been described), first, in Dimensions; these not being so deep, because they being made in the very Beams, their upper Edges are in the upper Surface of the Beams, and their Holes at the Bottom, being about the Eighth of an Inch deep. The Depth of the Funnels must want the Eighth of an Inch of the Thickness of the Beams; but we make each Funnel an Inch and a quarter broader at Top than its Beam, by adding a Piece of Wood to each Side of its Beam, which reaches down about half-way its Thickness; and these Pieces being firmly fix’d on by Nails, to the Sides of each Beam, the Legs of the Harrow take hold of these Pieces, which are in the Inside of these Beams. When the Plough is taken up to be turn’d, the Man who turns it takes hold of the Head of the Harrow with one Hand, and lays the other upon the Hopper, or Spindle, to keep it level, and to prevent either of the fore Wheels from striking against the Ground, whilst the Plough is turning round.

Another Difference there is between the Shape of these hinder Funnels from that of the former, to wit, That each fore Side of the hinder Trunks must not be quite so oblique as the rest; because then the upper Edge of these fore Sides might be too near the Tenons of the Sheats, and there might not be sufficient Wood betwixt them, to prevent the Sheats from being torn out; a thing which has never happen’d, that I know of. We sometimes make these hinder Funnels of a roundish Shape, like a Cone inverted; except that the Part which is next the Sheat, is not so oblique as the rest, for the Reason already given.

The only Advantage proposed by this roundish Shape is, that there is less Wood taken out than from the square Corners, and therefore more Wood for the added Pieces to be fastened to the Beams, than, in the square Funnels.

M and N are Two Pieces of Wood, each Eleven Inches long, Two Inches broad, and Two Inches thick: These are screw’d on near each End of the Plank, by Two Screws and Nuts each: They stand parallel to the other Beams, and have each a double Standard or Fork, O and P, in them, perpendicular to the Plank; by which Standards the fore Hopper is drawn and guided, in the manner as is seen in Fig. 21.

These Standards ought to be braced (or spurr’d) before and behind, and on their Outsides; they never being press’d inwards, have no occasion of Braces there: These are to be so placed, that when the Spindle is in their Forks, it may be exactly over the Hole of the Funnel, so that the Seed may drop into the Middle of it, when the Plough stands upon an horizontal Surface, the Spindle being also exactly parallel to the fore Edge of the Plank.

Fig. 10. is D in the Plough Fig. 1. It is Two Feet long, Two Inches broad in its narrowest Part, and half an Inch thick in the thinnest Part, and Two Inches at its Shoulders above the Plank. It is pinn’d thro’ the Plank before the Funnel, having one of its Legs on each Side the Tenon of the Sheat: It stands perpendicular to the Plank: Its only Use is to hold the fore Hopper from turning upon the Spindle, being put thro’ a thing (Fig. 22.) like the Carrier of a Latch, nail’d onto the upper Part of the fore Side of the fore Hopper, in which thing this Standard has room to play, or move side-ways, to the end that either Wheel may rise up.

Fig. 11. is one of the hinder Standards, which being placed in the Beam, as G or H, perpendicular to it, is driven into a Mortise, and pinn’d into the Beam. It has a Shoulder behind, and another before, and a Third on its Outside; which Shoulders serve instead of Braces, to keep it from moving backwards, forwards, or outwards: It is Two Feet Four Inches long, Two Inches broad, and an Inch thick: It is placed with its broad or flat Sides towards the Sides of the Beams. It is made so thin, because it should have the more room for the Hopper to play on it; and therefore must have its Strength in its Breadth. The Part at a must stand foremost.

The Standards G and H are both alike, except as they are opposite: Their Use is to draw, guide, and hold up the hinder Hopper: They are to be placed perpendicular to the Beams, and at equal Distance from each Side of those Beams, and at such a Distance before the Funnels, that when the fore Side of the Hopper by its whole Length bears against the hinder Surface of the Standards, the Seed may drop into the Middle of both Funnels, the Plough standing upon an horizontal Surface.

Be sure to take care, that the Sheats, Funnels, and Standards, be so placed, that the Spindle of the Hopper may be at right Angles with the Beams.

Q and R Part of the Limbers, which are also called Shafts, Sharps, and Thills; from whence the Horse that goes in them is call’d a Thiller. These Limbers are screw’d down to the Plank, by Two Screws and Nuts each. The Limbers are kept at their due Distance by the Bar S; near each End of which Bar, there is a Staple with a Crook underneath each Limber, to which is hitch’d, or fastened, a Link of each Trace, for drawing the Plough. This Bar is parallel to the Plank, and Seven Inches and an half before its fore Edge.

The Limbers must be mounted higher or lower at their fore Ends, according to the Height of the Horse that draws in them; and this may be done by the Screws that hold them to the Plank, and by cutting away the Wood at the Two hinder Screws, or at the Two foremost Screws, or by Wedges.

Every Workman knows how to team the Limbers; that is, to place them so on the Plank, that the Path of the Horse, which goes in the Middle betwixt them, may be parallel to all the Shares, and so that a Line, drawn in the Middle of this Path, might fall into a strait Line with the fore Share, standing on the same even Surface with the Path; for otherwise the Plough will not follow directly after the Horse, but will incline to one Side.

The Use of the Trunks of this Plough is for makeing the Chanels narrow, of whatsoever Depth they are: But, without Trunks, the Chanels must be made wide by Ground-wrists, which spread the Sides of the Chanels wide asunder, to the end that they may lie open for receiving of the Seed; and the deeper they are, the wider they must be: By this Width of a Chanel, the Seed in it is with more Difficulty cover’d, and the Chanel fill’d with the largest Clods, and the Seed comes up of a great Breadth, perhaps Three or Four Inches wide, so that the Weeds coming therein are hard to be gotten out.

To avoid these Inconveniences of wide Chanels, I contrived Trunks like those described, except that they were but Five or Six Inches high; and the Tops of their Plates, bending outwards from each other, form’d Two Sides of a Funnel; and the Wood between the Two Plates, being cut bevel at the Top, was as the fore Side of a Funnel to this Trunk: It was open behind from Top to Bottom: The Wheels were low, and the Seed-boxes narrow: The Seed in these Chanels was easily cover’d, especially those Sorts which were sown in dry Weather; for then the finest Mould would run in, and cover the Seed, as soon as the Trunks were past it.

The Seed in such a narrow Chanel comes up in a Line, where the Row not being above a Quarter of an Inch broad, scarce any Weeds come in it; and when the Weather is dry, the Earth of the Chanel not lying open to be dry’d, the Seed comes up the sooner.

I had Two Reasons for making of these Trunks higher, as they are now used: The one was, to avoid the too great Length of the Shares; and my other Reason was, that with those low Trunks, and long Shares, there could not be Two Ranks of Shares, and their Hoppers in the Plough, which are necessary for making very narrow Partitions, and absolutely necessary for planting this treble Row of Wheat; for if Three Shares for making the Seven-inch Partitions were placed in one Rank, the Mould (which is always moist or wet, when we plant Wheat) would be driven before the Shares, there not being room for it to pass betwixt them.

Fig. 12. is one End of the hinder Hopper laid open. I call it one End (altho’ it be an intire Box by itself) because this Hopper is supposed to have its middle Part cut out, to have a clearer Sight of the Plough, and fore Hopper; as is seen in Fig. 15. which is the whole Hopper in Two Parts. In this Fig. 12, A is the Inside of one End of the Hopper, made with several Pieces of half-inch Elm-board nail’d on to the Post c a, on the fore Side; which Post is a little more than half an Inch square, and Seventeen Inches and Three quarters long, being the Depth of that Part of the Hopper which holds the Seed. B is the fore Side of this Hopper; which must be nail’d on to the said Pod, being of the same Length with it, and Four Inches broad, and half an Inch thick; and this is the Part which on its Outside goes against the right-hand Standard of the Plough, when it is at Work. The other Post b d, of the same Thickness with the former, is nail’d in within half an Inch of the opposite Edge of this End; to which Post also C being nail’d, makes the hinder Side of this Part of the Hopper. C is Four Inches broad, and half an Inch thick; and both it, and the Post to which it is to be nail’d, are something longer than its opposite Side, because the Side B makes right Angles with the Top and Bottom of the Hopper; but the hinder Side C makes oblique Angles with the Top and Bottom of the Hopper; and the Reason of this is, because when the Hopper is full of Seed, it may be equally pois’d on the Spindle; which it could not be without this Bevel, unless the Bottom of the Hopper did come as much behind the Spindle as before it; and that would hinder the Person that follows the Drill, from seeing the Seed fall out of the Seed-box into the Funnel; and that Part of the Bottom which is before the Spindle cannot be made shorter, because that Part of the Seed-box which is before the Spindle, is (upon account of its Tongue) much longer than the Part of it which is behind the Spindle. ’Tis true that when the Hopper is empty of Seed, it cannot be thus pois’d; but then, being so light, it does not require it. e f g h is a Piece of a Board, nail’d on to that Part of the End A, which is below the Bottom of the Cavity which holds the Seed, and is commonly plac’d a little cross the Grain of the Board to which it is nail’d, and serves to strengthen it, and keeps the Hole i from splitting. The upper Edge e f of this added Piece of Board is exactly the Length of the Bottom of the Hopper, whereto the Brass Seed-box is fastened; and this Bottom, together with its Seed-box under it, being put into its Place, bears upon this Piece from e to f, which holds Up the right Side of the Bottom, and keeps it from sinking downwards; as the lower Ends of the Two mention’d Posts, and the fore and hinder Side B and C nail’d to them, prevent its rising upwards.