Part 2

Stomoxys calcitrans L.

Haematobia irritans L.

=TYPES OF TRAPS=

The same general principle is involved in nearly all flytraps in use, though superficially they may appear quite different. The flies are attracted into a cage, as it were, by going through a passage the entrance of which is large and the exit small, so that there is little chance of the flies, once in, finding their way out again. This principle is modified to fit different conditions. For instance, the window trap, devised by C. F. Hodge, catches the flies as they endeavor to enter or leave a building; the garbage-can trap, for which Professor Hodge is also to be credited, catches the flies that have entered garbage cans; and the manure-box trap retains the flies bred from infested manure put into the box or pit.

The attractant used to induce flies to enter traps may consist of (1) food, as in baited traps; (2) odors, as in window traps placed in windows from which odors are emitted; and (3) light, as in traps on manure boxes. Of course, light is an important factor in the success of all traps, for, as is well known, flies have a marked tendency to go toward the light, and they usually enter the trap by flying toward the light after having been attracted beneath it by bait or after entering a room in search of food.

=CONICAL TRAPS=

A number of traps of this general type are on the market, but most of these are of small size. Nearly all are constructed with a dome instead of a cone, and on this account the catching power is reduced about one-third. Moreover, the farmer, dairyman, or anyone with a few tools can construct traps at a small fraction of the sale price of ready-made ones.

There are now being made by certain firms in the Southwest traps of the dimensions and with the desirable features discussed in the following pages. These traps are all metal and some are built so that they can be taken apart for shipment.

=THE CONICAL HOOP TRAP=

A trap which appears from extensive tests made by E. W. Laake and the writer to be best for effective trapping, durability, ease of construction and repair, and cheapness may be made as follows:

The trap consists essentially of a screen cylinder with a frame made of barrel hoops, in the bottom of which is inserted a screen cone. The height or the cylinder is 24 inches, the diameter 18 inches, and the cone is 22 inches high, and 18 inches in diameter at the base. Material necessary for this trap consists of four new or secondhand wooden barrel hoops, one barrel head, four laths, 10 feet of strips 1 to inches wide 1½ one-half inch thick (portions of old boxes will suffice), 61 linear inches of 12 or 14 mesh galvanized screening 24 inches wide for the sides of the trap and 41 inches of screening 26 inches wide for the cone and door, an ounce of carpet tacks, and two turn-buttons, which may be made of wood. The total cost of the material for this trap, if all is bought new at retail prices is about $1. In practically all cases, however, the barrel hoops, barrel head, lath, and strips can be obtained without expense. This would reduce the cost to that of the wire and tacks, which would be about 80 cents. If a larger number of traps are constructed at one time, the cost is considerably reduced.

One of these traps is illustrated in Figures 1 and 2. In constructing the trap two of the hoops are bent in a circle (18 inches in diameter on the inside), and nailed together, the ends being trimmed to give a close fit. These form the bottom of the frame (A), and the other two, prepared in a similar way, the top (B). The top (C) of the trap is made of an ordinary barrel head with the bevel edge sawed off sufficiently to cause the head to fit closely in the hoops and allow secure nailing. A square, 10 inches on the side, is cut out of the center of the top to form a door. The portions of the top (barrel head) are held together by inch strips (D) placed around the opening one-half inch from the edge to form a jamb for the door. The door consists of a narrow frame (E) covered with screen (F) well fitted to the trap and held in place (not hinged) by buttons (G). The top is then nailed in the upper hoops and the sides (H) formed by closely tacking screen wire on the outside of the hoops. Four laths (I) (or light strips) are nailed to the hoops on the outside of the trap to act as supports between the hoops, and the ends are allowed to project 1 inch at the bottom to form legs (J). The legs are made to project inches when the traps are to be used with bait pans 4 inches deep in trapping screw-worm flies. The cone (K) is cut from the screen and either sewed with fine wire or soldered where the edges meet at (L), or a narrow lath may be nailed along these edges. The apex of the cone is then cut off to give an aperture (M) 1 inch in diameter. It is then inserted in the trap and closely tacked to the hoop around the base.

The construction of a cone of any given height or diameter is quite simple if the following method be observed. It is best to cut a pattern from a large piece of heavy paper, cardboard, or tin. Figure 3 illustrates the method of laying out a cone of the proper dimensions for the above trap. An ordinary square is placed on the material from which the pattern is to be cut; a distance (22 inches) equal to the height of the cone is laid off on one leg of the square at A, and a distance (9 inches) equal to one-half of the diameter of the base of the cone is laid off on the other leg at B, and a line is drawn between the points A and B. With the distance between these points as a radius and with the point A as a center, the portion of a circle, CD, is drawn. With a pair of dividers, the legs of which are set 1 inch apart, or with the square, lay off as many inches on the arc CD, starting at C, as there are inches around the base of the cone, which in this case is about 56½ inches, reaching nearly to the point E. Then add one-half inch for the lapping of the edges of the cone, and one-half inch which is taken up when the cone is tacked in, thus making a total distance from C to E of 57½ inches. Draw a line from A to C and another from A to E, and cut out the pattern on these lines and on the arc from C to E, as shown in Figure 3. The edges AC and AE are then brought together, lapped one-half inch, and sewed with wire or soldered. After the aperture of the cone is formed by cutting off the apex, as previously described, it is ready for insertion in the trap.

In order to figure the distance around the base of a cone of any given diameter, multiply the diameter by 3.1416 or 3-1/7.

The height of the legs of the trap, the height of the cone, and the size of the aperture in the top of the cone, each is of importance in securing the greatest efficiency.

=OTHER FORMS OF CONICAL TRAPS=

A modification of the previously described trap has been made by D. C. Parman of the Bureau of Entomology. The principal point of advantage in this type is that it can be made more quickly and with fewer tools. The principles and dimensions are the same, the most striking difference being the absence of a wooden top. A single hoop with the thick edge down forms the upper frame of the cylinder and the entire top is made of screen. A circular piece of screen with a diameter about 3 inches greater than the diameter of the cylinder is cut; a hoop with a diameter equal to the inside of the top of the trap is then made of heavy wire and laid upon the disk of screen and the edges of the screen bent in over it. By folding in and crimping the edges of the wire over the wire hoop it will remain in position without difficulty and the edges of the screen disk are used to lift the top of the trap out for emptying flies. It is important to have the screen top fit the inside of the cylinder very snugly at all points. If there is any space left where flies can escape it is a good plan to bind the edge of the top with a strip of burlap. This not only helps to close the openings but keeps the hoop in place and aids in removing the top. Another difference is that the screen forming the sides of the cylinder is placed on the inside of the hoops and legs, the frame being built first and then the cylinder formed by tacking the wire on the inside of the hoops and nailing in along the upright strips and against the wire short pieces of laths with their upper ends against the lower edge of the hoop forming the top of the trap and extending downward along the legs about two-thirds of their length. These strips hold the wire in place and give rigidity to the trap, and they are thick enough to project beyond the inner surface of the hoop and form a support upon which the edges of the screen top rest.

Conical traps with galvanized-iron frames are satisfactory, but they are less easily rescreened. These, of course, can be constructed only by shops with considerable equipment. Traps constructed with a wooden disk about the base of the cone, and a similar disk around the top to serve as a frame, or those with a square wooden frame at the bottom and top, with strips up the corners, are fairly satisfactory. It should be borne in mind, however, that the factor which determines the number of flies caught is the diameter of the base of the cone, if other things are equal. Therefore, the space taken up by the wooden framework is largely wasted, and if it is too wide it will have a deterrent effect on the flies which come toward the bait. For this reason it is advisable that the wood around the base of the cone should be as narrow as consistent with strength--usually about 3 inches.

Under no condition should the sides or top of the trap be of solid material, as the elimination of light from the top or sides has been found to decrease the catch from 50 to 75 per cent.

=ALL-METAL FLYTRAP=

Where large numbers of traps are to be constructed, and especially if they are to be used for trapping screw-worm flies on the range, it is desirable to make them with metal rather than wooden frames. Traps with galvanized-iron frames are now being used extensively on ranches in central and western Texas in combating the screw-worm fly. Mechanics may wish to vary details of construction from those given in the specifications, but the dimensions and general features of the trap should not be altered. The cost of the metal-framed traps varies from about $3.50 to $5 each according to the number ordered, the workmanship, and the kind of materials used. For the guidance of those who desire such traps the following directions, together with a working drawing (fig. 4), are given:

=SPECIFICATIONS=

Dimensions--As per working drawing.

Wire--14-mesh galvanized or preferably copper screen wire.

Cylinder--Wire gauze, to be soldered completely around inside of top ring and at intervals of 2 inches or less in groove of bottom ring. Vertical seam to be soldered entire and placed behind one leg. Where shipment of traps is not contemplated the diameter of the top of the cylinder may be the same as that of the bottom.

Top--Wire gauze to be soldered completely around periphery on inside of top ring.

Cone--Wire gauze to be soldered completely around inside of cone ring and vertically along seam. A 1-inch inlet hole shall be formed at apex of cone.

Frame--To be made of 24-gauge galvanized iron. This includes top and bottom rings and legs.