Part 46

Fig. 6. Old-Style Sales Book. Underwood Typewriter Co. ]

If the person who did the copying did not use due care, the paper would be too wet and the ink would run and blur the copy and the invoice. If two invoices were accidently picked up by the person copying, the top invoice would not be copied on the tissue sheet. This is a most serious objection, for the reason that the copy in the tissue was used as record of the invoice for the purpose of posting into the ledger.

Another difficulty was the usual one experienced through the use of bound books in office work. Only one person can use a book at one time. If Fayette Henry, the accountant, was using the tissue-copy book, and Dave Pike, the order clerk, wanted to use it to see if all invoices had been copied by the office boy, he had to wait on Fayette Henry. The loose-leaf sales sheet shown in Fig. 7, with the pages serially numbered and placed in proper binders after each sheet has been filed, overcomes all of the difficulties mentioned—with many additional benefits.

Fig. 7. Loose-Leaf Sales Sheet and Invoices. No Ruling on Sales Sheet. Remington Typewriter Co. ]

The loose-leaf sales sheet and invoice were first used with the flat-bed billing machine, the sales sheet being held in position by being placed over studs (round metal posts), which fitted into the punched holes in the edge of the paper. These punched holes were used ultimately for fitting over the metal binder posts in the loose-leaf binders. The invoices were wider than the regular-size invoice and were perforated about 1 inch or 1½ inches from the left side, as shown in Fig. 8. To the left of the perforated edge were two small holes about 2¾ inches apart, which fitted over two small studs on a sliding bill-holder device. This plan provided a means of holding the large sheet and invoice in proper relation to each other. A piece of carbon paper the same size as the sales sheet was placed between the invoice and the sales sheet. This ruling of the sales sheet is shown in Fig. 9.

Fig. 8. Invoice for Use on Billing Machine ]

When an invoice was written on the billing machine, it was manifolded on the sales sheet beneath. When the invoice was finished it was ready to mail—no delay in copying invoices, no blurred invoices through careless copying. No fading of the manifolded copy where black carbon paper was used. Inks are not made of indestructible carbons as black carbon paper is made. A condensed billing or invoicing loose-leaf sales book for this purpose is shown in Fig. 10.

The following are some of the many good features of the condensed system, as it is in use to-day, briefly stated:

Fig. 9. Loose-Leaf Sales Sheet ]

Bill and entry in sales book are obtained at one operation.

Entries upon sales book agree absolutely with bill rendered.

The bill clerk becomes bill and entry clerk combined.

There is no danger of a bill being rendered without the proper charge being made.

Entries under this system occupy but one-fourth the space required for those written with the pen.

There is no waste space upon sales sheet.

Both sides of the sales sheet may be utilized.

The saving in vault space alone is worthy of special consideration.

Fig. 10. Condensed Billing or Invoicing Loose-Leaf Sales Book. Underwood Typewriter Co. ]

In recent years, the typewriter companies have placed devices on their typewriters which permit of the sales sheet being held independently of the invoices. This permits one to hold the large sales sheet in the machine until enough invoices have been manifolded thereon to cover the page, at which time the sales sheet is reversed. The invoices can be placed in the machine and removed therefrom after being written, without interfering with the sales sheet. No extra width of invoice is required, which permits of old stationery being used in the form of invoices. The flat-bed machines can use old stationery, but not quite so well. However, when billing by machinery, it is false economy to use stationery designed for pen work. The reasons for this will be touched upon later.

The use of two ledgers necessitates the use of two columns at the right side of the page. All names from A to L are placed in the first column; all names from M to Z are placed in the second. For instance, an invoice reading as shown in the sales journal, Fig. 11, illustrates the idea of writing the totals in the two columns at the right side of sheet according to the initials of the last name of the firm or the individual, as the respective ledgers are arranged in that manner. If at the end of the month the first column shows a total of $3,000.00 the bookkeeper knows that he has posted that amount into Ledger A-L, etc.

The above plan enables the bookkeeper to add separately the totals which are posted to the respective ledgers. The desire to separate the charges to a country ledger and a city ledger can be accomplished by using two columns in the same way.

The desire to place all credit memoranda in the sales book can be accomplished by using two columns in the sales book as noted above. The first column is used for the charges, and the second one for entering the credits. One difficulty arises in connection with this plan. Credits are liable to be entered in the debit column. To obviate this, the invoices are made just wide enough to reach over the first column, the credit memoranda are made wider to reach over the last column. When an amount is written in the last column of the invoice, it manifolds in the proper column of the sales sheet. The same is true of an amount written in the last column of a credit memo.

This subdivision of columns is carried a step further to permit of the analyzation of sales in several ways.

According to classes of goods, as follows:

LAMSON FOUR-INCH PNEUMATIC TUBE ORDER CARRYING SYSTEM FOR A LARGE WHOLESALE ESTABLISHMENT OR A FACTORY Lamson Consolidated Store Service Co. ]

Fig. 11. Sales Journal Arranged for Distribution to Two Ledgers ]

According to territory, as follows:

According to salesmen, as follows: